Klipper/Config_Reference — German @ Hosted Weblate: Configuration reference

English

German

Actions

[samd_sercom my_sercom]
sercom:
# The name of the sercom bus to configure in the micro-controller.
# Available names are "sercom0", "sercom1", etc.. This parameter
# must be provided.
tx_pin:
# MOSI pin for SPI communication, or SDA (data) pin for I2C
# communication. The pin must have a valid pinmux configuration
# for the given SERCOM peripheral. This parameter must be provided.
#rx_pin:
# MISO pin for SPI communication. This pin is not used for I2C
# communication (I2C uses tx_pin for both sending and receiving).
# The pin must have a valid pinmux configuration for the given
# SERCOM peripheral. This parameter is optional.
clk_pin:
# CLK pin for SPI communication, or SCL (clock) pin for I2C
# communication. The pin must have a valid pinmux configuration
# for the given SERCOM peripheral. This parameter must be provided.

[probe]
pin:
# Probe detection pin. If the pin is on a different microcontroller
# than the Z steppers then it enables "multi-mcu homing". This
# parameter must be provided.
#deactivate_on_each_sample: True
# This determines if Klipper should execute deactivation gcode
# between each probe attempt when performing a multiple probe
# sequence. The default is True.
#x_offset: 0.0
# The distance (in mm) between the probe and the nozzle along the
# x-axis. The default is 0.
#y_offset: 0.0
# The distance (in mm) between the probe and the nozzle along the
# y-axis. The default is 0.
z_offset:
# The distance (in mm) between the bed and the nozzle when the probe
# triggers. This parameter must be provided.
#speed: 5.0
# Speed (in mm/s) of the Z axis when probing. The default is 5mm/s.
#samples: 1
# The number of times to probe each point. The probed z-values will
# be averaged. The default is to probe 1 time.
#sample_retract_dist: 2.0
# The distance (in mm) to lift the toolhead between each sample (if
# sampling more than once). The default is 2mm.
#lift_speed:
# Speed (in mm/s) of the Z axis when lifting the probe between
# samples. The default is to use the same value as the 'speed'
# parameter.
#samples_result: average
# The calculation method when sampling more than once - either
# "median" or "average". The default is average.
#samples_tolerance: 0.100
# The maximum Z distance (in mm) that a sample may differ from other
# samples. If this tolerance is exceeded then either an error is
# reported or the attempt is restarted (see
# samples_tolerance_retries). The default is 0.100mm.
#samples_tolerance_retries: 0
# The number of times to retry if a sample is found that exceeds
# samples_tolerance. On a retry, all current samples are discarded
# and the probe attempt is restarted. If a valid set of samples are
# not obtained in the given number of retries then an error is
# reported. The default is zero which causes an error to be reported
# on the first sample that exceeds samples_tolerance.
#activate_gcode:
# A list of G-Code commands to execute prior to each probe attempt.
# See docs/Command_Templates.md for G-Code format. This may be
# useful if the probe needs to be activated in some way. Do not
# issue any commands here that move the toolhead (eg, G1). The
# default is to not run any special G-Code commands on activation.
#deactivate_gcode:
# A list of G-Code commands to execute after each probe attempt
# completes. See docs/Command_Templates.md for G-Code format. Do not
# issue any commands here that move the toolhead. The default is to
# not run any special G-Code commands on deactivation.

[display]
lcd_type:
# The type of LCD chip in use. This may be "hd44780", "hd44780_spi",
# "st7920", "emulated_st7920", "uc1701", "ssd1306", or "sh1106".
# See the display sections below for information on each type and
# additional parameters they provide. This parameter must be
# provided.
#display_group:
# The name of the display_data group to show on the display. This
# controls the content of the screen (see the "display_data" section
# for more information). The default is _default_20x4 for hd44780
# displays and _default_16x4 for other displays.
#menu_timeout:
# Timeout for menu. Being inactive this amount of seconds will
# trigger menu exit or return to root menu when having autorun
# enabled. The default is 0 seconds (disabled)
#menu_root:
# Name of the main menu section to show when clicking the encoder
# on the home screen. The defaults is __main, and this shows the
# the default menus as defined in klippy/extras/display/menu.cfg
#menu_reverse_navigation:
# When enabled it will reverse up and down directions for list
# navigation. The default is False. This parameter is optional.
#encoder_pins:
# The pins connected to encoder. 2 pins must be provided when using
# encoder. This parameter must be provided when using menu.
#encoder_steps_per_detent:
# How many steps the encoder emits per detent ("click"). If the
# encoder takes two detents to move between entries or moves two
# entries from one detent, try changing this. Allowed values are 2
# (half-stepping) or 4 (full-stepping). The default is 4.
#click_pin:
# The pin connected to 'enter' button or encoder 'click'. This
# parameter must be provided when using menu. The presence of an
# 'analog_range_click_pin' config parameter turns this parameter
# from digital to analog.
#back_pin:
# The pin connected to 'back' button. This parameter is optional,
# menu can be used without it. The presence of an
# 'analog_range_back_pin' config parameter turns this parameter from
# digital to analog.
#up_pin:
# The pin connected to 'up' button. This parameter must be provided
# when using menu without encoder. The presence of an
# 'analog_range_up_pin' config parameter turns this parameter from
# digital to analog.
#down_pin:
# The pin connected to 'down' button. This parameter must be
# provided when using menu without encoder. The presence of an
# 'analog_range_down_pin' config parameter turns this parameter from
# digital to analog.
#kill_pin:
# The pin connected to 'kill' button. This button will call
# emergency stop. The presence of an 'analog_range_kill_pin' config
# parameter turns this parameter from digital to analog.
#analog_pullup_resistor: 4700
# The resistance (in ohms) of the pullup attached to the analog
# button. The default is 4700 ohms.
#analog_range_click_pin:
# The resistance range for a 'enter' button. Range minimum and
# maximum comma-separated values must be provided when using analog
# button.
#analog_range_back_pin:
# The resistance range for a 'back' button. Range minimum and
# maximum comma-separated values must be provided when using analog
# button.
#analog_range_up_pin:
# The resistance range for a 'up' button. Range minimum and maximum
# comma-separated values must be provided when using analog button.
#analog_range_down_pin:
# The resistance range for a 'down' button. Range minimum and
# maximum comma-separated values must be provided when using analog
# button.
#analog_range_kill_pin:
# The resistance range for a 'kill' button. Range minimum and
# maximum comma-separated values must be provided when using analog
# button.

sensor_type:
# One of "EPCOS 100K B57560G104F", "ATC Semitec 104GT-2",
# "ATC Semitec 104NT-4-R025H42G", "Generic 3950",
# "Honeywell 100K 135-104LAG-J01", "NTC 100K MGB18-104F39050L32",
# "SliceEngineering 450", or "TDK NTCG104LH104JT1"
sensor_pin:
# Analog input pin connected to the thermistor. This parameter must
# be provided.
#pullup_resistor: 4700
# The resistance (in ohms) of the pullup attached to the thermistor.
# The default is 4700 ohms.
#inline_resistor: 0
# The resistance (in ohms) of an extra (not heat varying) resistor
# that is placed inline with the thermistor. It is rare to set this.
# The default is 0 ohms.

English	German
Configuration reference	Konfigurationsreferenz	Config_Reference

English

German

Configuration reference

Konfigurationsreferenz

Config_Reference

Klipper

Config_Reference Glossary

German

Translate

Glossary term

Things to check

Reused translation

Glossary

String information

Flags

Source string location

String age

Last updated

Source string age

Translation file

	English	German	Actions
	[duplicate_pin_override]	[duplicate_pin_override]
	This tool allows a single micro-controller pin to be defined multiple times in a config file without normal error checking. This is intended for diagnostic and debugging purposes. This section is not needed where Klipper supports using the same pin multiple times, and using this override may cause confusing and unexpected results.
	[duplicate_pin_override] pins: # A comma separated list of pins that may be used multiple times in # a config file without normal error checks. This parameter must be # provided.
	SAMD SERCOM configuration to specify which pins to use on a given SERCOM. One may define any number of sections with a "samd_sercom" prefix. Each SERCOM must be configured prior to using it as SPI or I2C peripheral. Place this config section above any other section that makes use of SPI or I2C buses.
	[samd_sercom my_sercom] sercom: # The name of the sercom bus to configure in the micro-controller. # Available names are "sercom0", "sercom1", etc.. This parameter # must be provided. tx_pin: # MOSI pin for SPI communication, or SDA (data) pin for I2C # communication. The pin must have a valid pinmux configuration # for the given SERCOM peripheral. This parameter must be provided. #rx_pin: # MISO pin for SPI communication. This pin is not used for I2C # communication (I2C uses tx_pin for both sending and receiving). # The pin must have a valid pinmux configuration for the given # SERCOM peripheral. This parameter is optional. clk_pin: # CLK pin for SPI communication, or SCL (clock) pin for I2C # communication. The pin must have a valid pinmux configuration # for the given SERCOM peripheral. This parameter must be provided.
	Configuration reference	Konfigurationsreferenz
	Controller cooling fan (one may define any number of sections with a "controller_fan" prefix). A "controller fan" is a fan that will be enabled whenever its associated heater or its associated stepper driver is active. The fan will stop whenever an idle_timeout is reached to ensure no overheating will occur after deactivating a watched component.
	See the [rotation distance document](Rotation_Distance.md) for information on calculating the `rotation_distance` parameter. See the [Multi-MCU homing](Multi_MCU_Homing.md) document for information on homing using multiple micro-controllers.
	[probe] pin: # Probe detection pin. If the pin is on a different microcontroller # than the Z steppers then it enables "multi-mcu homing". This # parameter must be provided. #deactivate_on_each_sample: True # This determines if Klipper should execute deactivation gcode # between each probe attempt when performing a multiple probe # sequence. The default is True. #x_offset: 0.0 # The distance (in mm) between the probe and the nozzle along the # x-axis. The default is 0. #y_offset: 0.0 # The distance (in mm) between the probe and the nozzle along the # y-axis. The default is 0. z_offset: # The distance (in mm) between the bed and the nozzle when the probe # triggers. This parameter must be provided. #speed: 5.0 # Speed (in mm/s) of the Z axis when probing. The default is 5mm/s. #samples: 1 # The number of times to probe each point. The probed z-values will # be averaged. The default is to probe 1 time. #sample_retract_dist: 2.0 # The distance (in mm) to lift the toolhead between each sample (if # sampling more than once). The default is 2mm. #lift_speed: # Speed (in mm/s) of the Z axis when lifting the probe between # samples. The default is to use the same value as the 'speed' # parameter. #samples_result: average # The calculation method when sampling more than once - either # "median" or "average". The default is average. #samples_tolerance: 0.100 # The maximum Z distance (in mm) that a sample may differ from other # samples. If this tolerance is exceeded then either an error is # reported or the attempt is restarted (see # samples_tolerance_retries). The default is 0.100mm. #samples_tolerance_retries: 0 # The number of times to retry if a sample is found that exceeds # samples_tolerance. On a retry, all current samples are discarded # and the probe attempt is restarted. If a valid set of samples are # not obtained in the given number of retries then an error is # reported. The default is zero which causes an error to be reported # on the first sample that exceeds samples_tolerance. #activate_gcode: # A list of G-Code commands to execute prior to each probe attempt. # See docs/Command_Templates.md for G-Code format. This may be # useful if the probe needs to be activated in some way. Do not # issue any commands here that move the toolhead (eg, G1). The # default is to not run any special G-Code commands on activation. #deactivate_gcode: # A list of G-Code commands to execute after each probe attempt # completes. See docs/Command_Templates.md for G-Code format. Do not # issue any commands here that move the toolhead. The default is to # not run any special G-Code commands on deactivation.
	[display] lcd_type: # The type of LCD chip in use. This may be "hd44780", "hd44780_spi", # "st7920", "emulated_st7920", "uc1701", "ssd1306", or "sh1106". # See the display sections below for information on each type and # additional parameters they provide. This parameter must be # provided. #display_group: # The name of the display_data group to show on the display. This # controls the content of the screen (see the "display_data" section # for more information). The default is _default_20x4 for hd44780 # displays and _default_16x4 for other displays. #menu_timeout: # Timeout for menu. Being inactive this amount of seconds will # trigger menu exit or return to root menu when having autorun # enabled. The default is 0 seconds (disabled) #menu_root: # Name of the main menu section to show when clicking the encoder # on the home screen. The defaults is __main, and this shows the # the default menus as defined in klippy/extras/display/menu.cfg #menu_reverse_navigation: # When enabled it will reverse up and down directions for list # navigation. The default is False. This parameter is optional. #encoder_pins: # The pins connected to encoder. 2 pins must be provided when using # encoder. This parameter must be provided when using menu. #encoder_steps_per_detent: # How many steps the encoder emits per detent ("click"). If the # encoder takes two detents to move between entries or moves two # entries from one detent, try changing this. Allowed values are 2 # (half-stepping) or 4 (full-stepping). The default is 4. #click_pin: # The pin connected to 'enter' button or encoder 'click'. This # parameter must be provided when using menu. The presence of an # 'analog_range_click_pin' config parameter turns this parameter # from digital to analog. #back_pin: # The pin connected to 'back' button. This parameter is optional, # menu can be used without it. The presence of an # 'analog_range_back_pin' config parameter turns this parameter from # digital to analog. #up_pin: # The pin connected to 'up' button. This parameter must be provided # when using menu without encoder. The presence of an # 'analog_range_up_pin' config parameter turns this parameter from # digital to analog. #down_pin: # The pin connected to 'down' button. This parameter must be # provided when using menu without encoder. The presence of an # 'analog_range_down_pin' config parameter turns this parameter from # digital to analog. #kill_pin: # The pin connected to 'kill' button. This button will call # emergency stop. The presence of an 'analog_range_kill_pin' config # parameter turns this parameter from digital to analog. #analog_pullup_resistor: 4700 # The resistance (in ohms) of the pullup attached to the analog # button. The default is 4700 ohms. #analog_range_click_pin: # The resistance range for a 'enter' button. Range minimum and # maximum comma-separated values must be provided when using analog # button. #analog_range_back_pin: # The resistance range for a 'back' button. Range minimum and # maximum comma-separated values must be provided when using analog # button. #analog_range_up_pin: # The resistance range for a 'up' button. Range minimum and maximum # comma-separated values must be provided when using analog button. #analog_range_down_pin: # The resistance range for a 'down' button. Range minimum and # maximum comma-separated values must be provided when using analog # button. #analog_range_kill_pin: # The resistance range for a 'kill' button. Range minimum and # maximum comma-separated values must be provided when using analog # button.
	sensor_type: # One of "EPCOS 100K B57560G104F", "ATC Semitec 104GT-2", # "ATC Semitec 104NT-4-R025H42G", "Generic 3950", # "Honeywell 100K 135-104LAG-J01", "NTC 100K MGB18-104F39050L32", # "SliceEngineering 450", or "TDK NTCG104LH104JT1" sensor_pin: # Analog input pin connected to the thermistor. This parameter must # be provided. #pullup_resistor: 4700 # The resistance (in ohms) of the pullup attached to the thermistor. # The default is 4700 ohms. #inline_resistor: 0 # The resistance (in ohms) of an extra (not heat varying) resistor # that is placed inline with the thermistor. It is rare to set this. # The default is 0 ohms.