Klipper/Config_checks — Italian @ Hosted Weblate: Navigate to the temperature graph section and type in 50 …

Translation

English

Navigate to the temperature graph section and type in 50 followed by enter in the extruder/tool temperature box. The extruder temperature in the graph should start to increase (within about 30 seconds or so). Then go to the extruder temperature drop-down box and select "Off". After several minutes the temperature should start to return to its initial room temperature value. If the temperature does not increase then verify the "heater_pin" setting in the config.

Italian

Needs editing

Skip

	English	Italian	Actions
	It may be necessary to perform other types of detailed printer calibration - a number of guides are available online to help with this (for example, do a web search for "3d printer calibration"). As an example, if you experience the effect called ringing, you may try following [resonance compensation](Resonance_Compensation.md) tuning guide.	Potrebbe essere necessario eseguire altri tipi di calibrazione di dettaglio in riferimento alla stampante: sono disponibili numerose guide online per questo scopo (ad esempio, eseguire una ricerca sul Web per "calibrazione della stampante 3d"). Ad esempio, se si verifica l'effetto chiamato risonanza, è possibile provare a seguire la calibrazione tramite l'istruzione [compensazione della risonanza](Resonance_Compensation.md).
	Configuration checks	Controlli della configurazione
	Klipper supports [PID control](https://en.wikipedia.org/wiki/PID_controller) for the extruder and bed heaters. In order to use this control mechanism, it is necessary to calibrate the PID settings on each printer (PID settings found in other firmwares or in the example configuration files often work poorly).	Klipper supporta il sistema [controllo PID](https://en.wikipedia.org/wiki/PID_controller) per iriscaldatori dell'estrusore e del piatto. Per utilizzare questo sistema di controllo, è necessario calibrare le impostazioni PID su ciascuna stampante (le impostazioni PID presenti in altri firmware o nei file di configurazione di esempio spesso funzionano male).
	Start by verifying that temperatures are being properly reported. Navigate to the temperature graph section in the user interface. Verify that the temperature of the nozzle and bed (if applicable) are present and not increasing. If it is increasing, remove power from the printer. If the temperatures are not accurate, review the "sensor_type" and "sensor_pin" settings for the nozzle and/or bed.	Inizia verificando che le temperature siano riportate correttamente. Naviga nella sezione della temperatura nell'interfaccia utente. Verifica che la temperatura del nozzle e del letto (se possibile) sono presenti e non aumentino. Nel caso aumentino, togli corrente alla stampante. Se le temperature non sono accurate, ricontrolla le impostazioni del nozzle e del letto chiamate "sensor_type" e "sensor_pin".
	Navigate to the command console and issue an M112 command in the terminal box. This command requests Klipper to go into a "shutdown" state. It will cause an error to show, which can be cleared with a FIRMWARE_RESTART command in the command console. Octoprint will also require a reconnect. Then navigate to the temperature graph section and verify that temperatures continue to update and the temperatures are not increasing. If temperatures are increasing, remove power from the printer.	Naviga nella console dei comandi e invia un comando M112 nel terminale. Questo comando chiede a Klipper di andare in uno stato di spegnimento. Ciò causerà un errore, che potrà essere risolto con l'esecuzione di un comando "FIRMWARE_RESTART" nella console. Anche octoprint richiederà una riconessione. Poi vai nella sezione delle temperature e verifica che esse continuino ad aggiornarsi e non incrementino. Se le temperature incrementano togliere immediatamente corrente alla stampante.
	Navigate to the temperature graph section and type in 50 followed by enter in the extruder/tool temperature box. The extruder temperature in the graph should start to increase (within about 30 seconds or so). Then go to the extruder temperature drop-down box and select "Off". After several minutes the temperature should start to return to its initial room temperature value. If the temperature does not increase then verify the "heater_pin" setting in the config.	Italiano
	Verify that all of the printer axes can manually move freely (the stepper motors are disabled). If not, issue an M84 command to disable the motors. If any of the axes still can not move freely, then verify the stepper "enable_pin" configuration for the given axis. On most commodity stepper motor drivers, the motor enable pin is "active low" and therefore the enable pin should have a "!" before the pin (for example, "enable_pin: !PA1").	Verifica che gli assi della stampante possano muoversi liberamente (I motori sono disabilitati). In caso contrario, inviare un comando M84 per disabilitare i motori. Se un asse qualunque non si potesse muovere liberamente, verificare la configurazione stepper "enable_pin" per gli assi in questione.Nella maggior parte dei driver per motori passo-passo, il pin di abilitazione del motore è "attivo basso" e pertanto il pin di abilitazione deve essere preceduto da un "!" (ad esempio, "enable_pin: !PA1").
	Manually move all the printer axes so that none of them are in contact with an endstop. Send a QUERY_ENDSTOPS command via the command console. It should respond with the current state of all of the configured endstops and they should all report a state of "open". For each of the endstops, rerun the QUERY_ENDSTOPS command while manually triggering the endstop. The QUERY_ENDSTOPS command should report the endstop as "TRIGGERED".
	If the endstop appears inverted (it reports "open" when triggered and vice-versa) then add a "!" to the pin definition (for example, "endstop_pin: ^PA2"), or remove the "!" if there is already one present.
	Use the STEPPER_BUZZ command to verify the connectivity of each stepper motor. Start by manually positioning the given axis to a midway point and then run `STEPPER_BUZZ STEPPER=stepper_x` in the command console. The STEPPER_BUZZ command will cause the given stepper to move one millimeter in a positive direction and then it will return to its starting position. (If the endstop is defined at position_endstop=0 then at the start of each movement the stepper will move away from the endstop.) It will perform this oscillation ten times.
	To test the extruder motor it will be necessary to heat the extruder to a printing temperature. Navigate to the temperature graph section and select a target temperature from the temperature drop-down box (or manually enter an appropriate temperature). Wait for the printer to reach the desired temperature. Then navigate to the command console and click the "Extrude" button. Verify that the extruder motor turns in the correct direction. If it does not, see the troubleshooting tips in the previous section to confirm the "enable_pin", "step_pin", and "dir_pin" settings for the extruder.

Loading…

eziosantellocco97

Translation added

English

Italian 8 characters edited Current translation Translated

3 weeks ago

eziosantellocco97

Contributor joined

Contributor joined 3 weeks ago

None

String updated in the repository

English

Italian 0 characters edited Empty

7 months ago

Browse all string changes

Things to check

Mismatched full stop

Source and translation do not both end with a full stop

Reset

Glossary

English	Italian
No related strings found in the glossary.

String information

Flags

md-text

Source string location

docs/Config_checks.md:block • 9 • (paragraph)

String age

7 months ago

Last updated

3 weeks ago

Source string age

7 months ago

Translation file

docs/locales/it/LC_MESSAGES/Config_checks.po, string 26